Model of door intended for industrial applications.
Models: PB1, PB2, PB3, PBE.
Sectional Door characterised by, for example: solid shaft
with cotter hole. Reinforced springs for 40.000 cycles,
(apart from exceptions specified by the client). Industrial
bearing depending on type of drum used.Cylindrical drums, mixed drums (cylindrical conical),
conical drums, these depend on the model of door made.
Industrial doors are all made for automation.
Standard Industrial Sectional Door, for industrial
constructions.
The lintel or master beam (space where springs are positioned)
must be at least 450 mm.
This model uses the interior cable bracket, which means
the cables or towlines go inside
the vertical guides, at the same time a “C” shaped
section is welded to the horizontal guide, which requires
a minimum space of 100 mm. to attach these vertical guides. The PB1 model uses
the cylindrical drum; its dimension varying depending
on the weight and size of the door, which means that the size
of the bearing to be used is directly related to the
drum model used.
Industrial Sectional Door with raised guides, for industrial constructions.
The lintel or master beam (space where the springs are positioned)
must be at least 450 mm and less than twice the height (light opening) of the door.In these cases, we raise the guides
and vertical sections, hence allowing the horizontal guides
to go as close as possible to the ceiling. This model uses the interior
cable bracket, which means the cables or towlines go inside
the vertical guides.At
the same time a “C” shaped section is welded
to the horizontal guide, which requires a minimum space of 100
mm. to attach these vertical guides. The PB2 model uses the mixed
drum; its dimension varying depending on the weight and
size of the door which means the size of the bearing to
be used is directly related to the drum model used.
ndustrial Sectional Door with vertical guide
for industrial constructions.
The lintel or master beam (space where the springs are positioned)
must be at least twice the height (light opening) of the door.In these cases, the guides and vertical
sections go up perpendicularly hence eliminating horizontal
guides.
This model uses the interior cablebracket which
means the cables or towlines go inside the vertical guides.At the same time various “C”
shaped sections are welded to the vertical guide and therefore
require a minimum space of 100 mm. to attach these vertical
guides.
The PB1 model uses the conical drum; its dimension varying
depending on the weight and size of the door which means the
size of the bearing to be used is directly related
to the drum model used.
ndustrial Sectional Door for special applications.Depending on requirements, both
PB1 and PB2 are made. An exceptional case is where to door should slide according to the
slope of the ceiling or similar limitation, whether to avoid
a gantry crane or other determining factor.
This model uses the interior cable bracket which means
the cables or towlines go inside the vertical guides.At the same time “C” shaped sections are
welded to the vertical guide and require a minimum space of
100 mm. to attach these vertical guides. The PBE model uses the drum
corresponding to the manufactured model, whether PB1 or PB2,
its dimension varying depending on the weight and size of
the door, which means the size of the bearing to be used
is directly related to the drum model used.
Sizes referring to guides, etc. are studied
for each case according to plans provided.
Industrial Sectional Door intended for maceration
warehouses, cold stores and places where a high level of airtightness
and insulation are required.Depending on the requirements, both PB1 and
PB2, PBE or PBE are manufactured.
Refrigerator doors allow a minimum temperature of 0 ºC.At temperatures below 0 ºC up to
a maximum of –25 ºC silicone hardiness is placed around
the door perimeter and on panel joints.
This model is characterised by the use of 75 mm thick panels,
special vertical outline for the correct channelling of panels,
special rubber joints for greater airtightness, double aluminium
in the lower part.
Door components, such as, drums,
brackets, etc. will depend on the model manufactured, whether
PB1, PB2, PB3, or PBE.
